How to Identify LED Polarity: Leads on Through-Hole, Markings on SMD
Anyone who has soldered a circuit board knows this: an LED wired backwards will not light up. Telling the anode from the cathode is actually not hard — the method just differs between through-hole and SMD packages, and marking habits vary between manufacturers. Below are the common identification methods; follow them when repairing boards or soldering samples.
1. Through-Hole LEDs: Check the Leads First, Then the Lens
The most common method for through-hole LEDs is lead length: the long lead is the anode (positive) and the short lead is the cathode (negative). This is the as-shipped standard for 3mm and 5mm round LEDs. If the leads have already been cut to equal length, look at the lens rim: the flange at the base has a flat edge (a small notch), and the side with the flat is the cathode. Another way is to look inside the lens: of the two metal lead frames, the larger one (shaped like a small flag) is the cathode and the smaller one is the anode. Take our 3mm round single-color LED as an example: check the lead length first and you confirm the orientation in three seconds. One more tip: when trimming leads, solder first and cut afterwards, or mark the anode lead with a marker before cutting, so you do not lose track.
2. SMD LEDs: The Marking Is on the Body
SMD LEDs have no long leads to inspect; polarity relies entirely on markings on the body. The tricky part is that markings are not fully unified across manufacturers. Common conventions:
| Package | Common Polarity Marking | Notes |
|---|---|---|
| 0603 | Green dot or stripe on the back points to the cathode | Needs a magnifier; always confirm with the datasheet |
| 0805 | Color dot or band on the back marks the cathode | Some manufacturers mark the side instead |
| 1206 | Color dot on the back or end face | Larger package, marking is easier to read |
| 2835 | Chamfered corner or color dot indicates the cathode | Lighting-grade package, large pads, easy to confirm |
Besides the LED body, the PCB silkscreen is an important reference: a properly designed board prints a line or a dot next to the cathode pad, or labels K (cathode) and A (anode). Align the LED marking with the silkscreen during placement and you will rarely go wrong. For small packages like our 0603 SMD LED, follow the polarity diagram in the datasheet — do not guess from another brand's convention.
3. Can't Tell? Measure with a Multimeter
When markings are worn off or parts arrive unlabeled, a multimeter is the most direct tool. Set it to the diode range: red probe on the assumed anode, black probe on the cathode. If the orientation is right, most LEDs glow faintly and the meter shows a forward drop of about 1.6–3V; reversed, it shows overload (OL). Red and yellow LEDs have lower drops; blue and white are higher. Note that some analog meters and low-output diode ranges struggle to light a white LED visibly — in that case, read the voltage drop instead. No multimeter at hand? A CR2032 coin cell (3V) works too: long lead to the positive face, short lead to the negative face; if it lights, the orientation is correct. This only suits red/yellow/green LEDs with drops below 3V; white and blue may not light or may glow dimly.
4. Will Reverse Connection Burn the LED? Common Misconceptions
The conclusion first: in ordinary low-voltage DC circuits, a reversed LED simply does not light and will not burn out, because a typical LED's reverse withstand voltage is around 5V and common supplies rarely exceed that. But in high-voltage situations such as 220V AC mains indication, reverse connection or excessive reverse peaks can break the LED down; such circuits need a series reverse-protection diode. A few more pitfalls to avoid: first, bi-color LEDs come in common-cathode and common-anode versions with completely different pinouts — do not wire them like single-color parts; second, RGB LEDs have four leads and the longest is the common terminal — check the datasheet before wiring; third, SMD polarity markings genuinely differ between manufacturers, so re-confirm them whenever you change suppliers. For through-hole pin definitions, see the specification drawings of each model in our through-hole LED series section.
About Hongcheng Optoelectronics
Dongguan Hongcheng Optoelectronics Co., Ltd. is a Guangyu Group member; the group has over 20 years in the optoelectronics industry. Our LEDs use Grade-A chips and 99.99% pure gold wire bonding, and are RoHS certified. We support customization, sampling and volume quotations. Tel/WeChat: 139 2571 4318, email: sales@led-hc.com / sales@hc-led168.com.
